Description S310-24P4S Overview Table 4-81 Basic information about the S310-24P4S Item Details Description S310-24P4S (24*10/100/1000BASE-T ports, 4*GE SFP ports, PoE , AC power) Part Number 98012201 Model S310-24P4S First supported version V600R022C10 Components Figure 4-27 S310-24P4S appearance This model has had changes to its appearance and branding (from CloudEngine to eKitEngine), and devices delivered over different periods may have different appearances but have no differences in functions. 1 One MODE button 2 Twenty-four 10/100/1000BASE-T PoE ports 3 Four 1000BASE-X ports 4 One console port 5 One RST button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button. 6 Ground screw NOTE: It is used with a ground cable. 7 Jack for AC power cable locking strap NOTE: The AC power cable locking strap is not delivered with the switch. 8 AC socket NOTE: It is used with an AC power cable. Ports Table 4-82 Ports on the S310-24P4S Port Connector Type Description Available Components 10/100/1000BASE-T PoE port RJ45 A 10/100/1000BASE-T PoE Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s. The port supports the PoE function. Ethernet cable 1000BASE-X port SFP A 1000BASE-X port can send and receive data at 1000 Mbit/s. GE eSFP optical modules GE-CWDM eSFP optical modules GE-DWDM eSFP optical modules GE SFP copper module Console port RJ45 The console port is connected to a console for on-site configuration. Console cable Indicators and Buttons Figure 4-28 Indicators on the Switch The S310-24P4S model is used as an example. Non-PoE models do not have PoE indicator and PoE mode. Table 4-83 Description of indicators on the switch No. Indicator Name Color Status Description 1 PWR Power module indicator – Off The switch is powered off. Green Steady on The power supply is normal. Yellow Steady on The power supply is abnormal. 2 SYS System status indicator – Off The system is not running. Green Fast blinking The system is starting. Green Steady on During the system startup preparation phase, the SYS indicator is steady green, which lasts for a maximum of 30 seconds. Green Slow blinking The system is running normally. Red Steady on The system does not work normally after registration, or a fan alarm or a temperature alarm has been generated. 3 PoE PoE indicator – Off The PoE mode is not selected. Green Steady on The PoE mode is selected, and service port indicators show the PoE status of each port. 4 MODE Mode switch button – – When you press this button once, the service port indicators change to the PoE mode and show the PoE status of each service port. When you press this button a second time, the service port indicators restore to the default mode and show the connection status and link activity of each service port. If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the PoE indicator is off. 5 – Service port indicator Meanings of service port indicators vary in different modes. For details, see Table 4-84. NOTE: If a power failure occurs on a device’s PCB board, indicators of the last four optical ports on the device’s front panel blink green cyclically at an interval of 1 second, with each indicator illuminating for 0.25 seconds. 6 ID ID indicator – Off The ID indicator is not used (default state). Blue Steady on The indicator identifies the switch to maintain. The ID indicator can be turned on or off remotely to help field engineers find the switch to maintain. Table 4-84 Description of service port indicators in different modes (one indicator for each port) Display Mode Color Status Description Default mode – Off The port is not connected or has been shut down. Green Steady on A link has been established on the port. Green Blinking The port is sending or receiving data. PoE mode – Off The port is not providing power to a powered device (PD). Green Steady on The port is providing power to a PD. Green Blinking The power of the PD connected to the port exceeds the power capacity of the port or the power threshold configured on the port. Alternatively, the PD does not comply with IEEE standards. Power Supply System The switch has a built-in AC power module and does not support pluggable power modules. The built-in power module can provide 400 W PoE power, which ensures full PoE power on 24 ports in compliance with 802.3af or on 13 ports in compliance with 802.3at. Heat Dissipation System The switch has two built-in fans for forced air cooling. Air flows in from the left side and front panel, and exhausts from the right side. When working properly at a normal temperature, the device meets the desktop-class noise requirements. However, the fan speed may be high and the noise may be loud during device startup. This figure only shows the airflow direction and does not depict the actual device. Technical Specifications Table 4-85 Technical specifications of the S310-24P4S <td class=”idp-ltr-html-cellrowbo Item Specification Dimensions without packaging (H x W x D) [mm(in.)] Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 220.0 mm (1.72 in. x 17.4 in. x 8.66 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the parts protruding from the rear panel): 43.6 mm x 442.0 mm x 227.0 mm (1.72 in. x 17.4 in. x 8.94 in.) Dimensions with packaging (H x W x D) [mm(in.)] 90.0 mm x 550.0 mm x 360.0 mm (3.54 in. x 21.65 in. x 14.17 in.) Chassis height [U] 1 U Chassis material Metal Weight without packaging [kg(lb)] 2.92 kg (6.44 lb) Weight with packaging [kg(lb)] 3.79 kg (8.36 lb) Typical power consumption [W] 40.07 W Typical heat dissipation [BTU/hour] 136.72 BTU/hour Maximum power consumption [W] Without PoE: 47.1 W Full PoE load: 491.66 W (PoE: 400 W) Maximum heat dissipation [BTU/hour] Without PoE: 160.71 Full PoE load: 1677.59 Show More Show Less
